MDS PREP

When missing right maxillary lateral incisor and canine are to be replaced with PFM restorations, the abutments used are
1. both central incisors and both the right premolars
2. the right central incisor and the first pre molar
3. the right central incisor and both the pre molars
4. both the. central incisors and the right first premolar

Prosthodontics Answer: 1

If lower teeth are seen above the lower lip when patient is speaking, it indicates all of the following except
1. Too much vertical lap of the teeth
2. Insufficient interocclusal space
3. Vertical space between the jaws is in excess
4. Occlusal plane set too high

Prosthodontics Answer: 2

The width of the gap between adjacent units to be soldered should be
1) 0.1 inch
2) 0.01 inch
3) 0.001 inch
4) 0.24 inch

Prosthodontics Answer: 3

In a cast partial denture wearer, the stresses transferred to abutment teeth are decreased if
1) Retentive arm of the clasp is less flexible
2) Edentulous span is long
3) Length of the clasp is increased
4) Clasp is active when placed on abutment teeth

Prosthodontics Answer: 2

The stability of the mandibular complete denture is enhanced
1) When the level of the occlusal plane is above the dorsum of the tongue
2) When the tongue rests on the occlusal surfaces of lowers at rest
3) When the lateral borders are extended below the external oblique ridge
4) All of the above

Prosthodontics Answer: 2

Only pure hinge movements of the mandible occur at
1) Centric occlusion
2) Centric relation
3) Lateral occlusion
4) Terminal hinge position

Prosthodontics Answer: 4

The finish line used in complete metal cast crown
1) Chamfer
2) Chamfer with bevel
3) Feather edge
4) Shoulder

Prosthodontics Answer: 1

MDS PREP

If lower teeth are seen above the lower lip when patient is speaking, it indicates all of the following except
1. Too much vertical lap of the teeth
2. Insufficient interocclusal space
3. Vertical space between the jaws is in excess
4. Occlusal plane set too high

The width of the gap between adjacent units to be soldered should be
1) 0.1 inch
2) 0.01 inch
3) 0.001 inch
4) 0.24 inch

In a cast partial denture wearer, the stresses transferred to abutment teeth are decreased if
1) Retentive arm of the clasp is less flexible
2) Edentulous span is long
3) Length of the clasp is increased
4) Clasp is active when placed on abutment teeth

The stability of the mandibular complete denture is enhanced
1) When the level of the occlusal plane is above the dorsum of the tongue
2) When the tongue rests on the occlusal surfaces of lowers at rest
3) When the lateral borders are extended below the external oblique ridge
4) All of the above

Only pure hinge movements of the mandible occur at
1) Centric occlusion
2) Centric relation
3) Lateral occlusion
4) Terminal hinge position

The finish line used in complete metal cast crown
1) Chamfer
2) Chamfer with bevel
3) Feather edge
4) Shoulder

"Squint" test is used as guide for selecting
1) Shade of teeth
2) Shape of teeth
3) Length of teeth
4) None of the above

Explore by subjects

Anatomy

Physiology

Biochemistry

Dental Materials

Dental Anatomy

Pathology

Microbiology

Pharmacology

Oral Pathology

Community Dentistry

Medicine

Surgery

Oral Medicine

Prosthodontics

Orthodontics

Periodontology

Oral Surgery

Conservative Dentistry

Endodontics

Pedodontics

Radiology

Anaesthesia

MDS PREP

If lower teeth are seen above the lower lip when patient is speaking, it indicates all of the following except 1. Too much vertical lap of the teeth 2. Insufficient interocclusal space 3. Vertical space between the jaws is in excess 4. Occlusal plane set too high

The width of the gap between adjacent units to be soldered should be1) 0.1 inch2) 0.01 inch3) 0.001 inch4) 0.24 inch

In a cast partial denture wearer, the stresses transferred to abutment teeth are decreased if1) Retentive arm of the clasp is less flexible2) Edentulous span is long3) Length of the clasp is increased4) Clasp is active when placed on abutment teeth

The stability of the mandibular complete denture is enhanced1) When the level of the occlusal plane is above the dorsum of the tongue2) When the tongue rests on the occlusal surfaces of lowers at rest3) When the lateral borders are extended below the external oblique ridge4) All of the above

Only pure hinge movements of the mandible occur at1) Centric occlusion2) Centric relation3) Lateral occlusion4) Terminal hinge position

The finish line used in complete metal cast crown1) Chamfer2) Chamfer with bevel3) Feather edge4) Shoulder

"Squint" test is used as guide for selecting 1) Shade of teeth2) Shape of teeth3) Length of teeth4) None of the above

Explore by subjects

If lower teeth are seen above the lower lip when patient is speaking, it indicates all of the following except
1. Too much vertical lap of the teeth
2. Insufficient interocclusal space
3. Vertical space between the jaws is in excess
4. Occlusal plane set too high

The width of the gap between adjacent units to be soldered should be
1) 0.1 inch
2) 0.01 inch
3) 0.001 inch
4) 0.24 inch

In a cast partial denture wearer, the stresses transferred to abutment teeth are decreased if
1) Retentive arm of the clasp is less flexible
2) Edentulous span is long
3) Length of the clasp is increased
4) Clasp is active when placed on abutment teeth

The stability of the mandibular complete denture is enhanced
1) When the level of the occlusal plane is above the dorsum of the tongue
2) When the tongue rests on the occlusal surfaces of lowers at rest
3) When the lateral borders are extended below the external oblique ridge
4) All of the above

Only pure hinge movements of the mandible occur at
1) Centric occlusion
2) Centric relation
3) Lateral occlusion
4) Terminal hinge position

The finish line used in complete metal cast crown
1) Chamfer
2) Chamfer with bevel
3) Feather edge
4) Shoulder

"Squint" test is used as guide for selecting
1) Shade of teeth
2) Shape of teeth
3) Length of teeth
4) None of the above